Hanger bolts S-10 / S-08 for Corrugated- and trapezoidal sheet PV-Mounting

Hanger bolt S-10 / S-08 Application
on Corrugated- or trapezoidal sheet roofs

Hanger bolts S-10 / S-08 Advantages:

Enables direct construction of a profile plane
for timber and steel purlins

Technical Data

S-10 Wood Hanger Bolt:

Item No.: S-10200-KV / Hanger Bolt, M10x200mm / Clamping Range: 30 - 65 mm
Item No.: S-10250-KV / Hanger Bolt, M10x250mm / Clamping Range: 70 - 115 mm
Item No.: S-10300-KV / Hanger Bolt, M10x300mm / Clamping Range: 110 - 165 mm
Item No.: S-12200-KV / Hanger Bolt, M12x200mm / Clamping Range: 30 - 65 mm
Item No.: S-12250-KV / Hanger Bolt, M12x250mm / Clamping Range: 70 - 115 mm
Item No.: S-12300-KV / Hanger Bolt M12x300mm / Clamping range: 110-165 mm

All hanger bolts pre-assembled with EPDM gasket and KV-40. Hanger bolt material: 1.4301 / A2. Clamp connector material: ENAW 6063.
DIBt^® - approval hanger bolt: Z-14.4-602
DIBt^® - approval cross connector: Z-14.4-827

Installation tool for S-10 wood hanger bolt
Drill / 13.00mm drill bit / 7.0mm wood drill bit / 7mm socket wrench / 15mm wrench

Installation of S-10 wood hanger bolt

Determine the rafter alignment and mark it with a chalk line.
Pre-drill the roof cladding with a diameter of 13.00mm.
Pre-drill the wood with a diameter of 7.00mm.
Screw the hanger bolt into the rafter at least 70mm deep.
Press the seal onto the roof surface by tightening the bottom nut until a slight bulge forms on the seal.

Accessories

Art.Nr.: P-40-6550-xxx / support profile 40x40mm
Art.Nr.: P-40-5500-xxx / support profile 40x40mm
Art.Nr.: P-80-6500-xxx / support profile 80x40mm
Art.Nr.: MMK-xxx-xxx / module middle clamp
Art.Nr.: MEK-xxx-xxx / module end clamp

P-40
P-80
MMK
MEK

Accessory Hanger bolt bridge

Art.Nr.: S-Brücke-333 / Hanger bolt bridge für Bead spacing 333 mm

Icluded in the set:

4 pieces / Washers M10 / DIN440 / 1.4301
1 Stück / cross connector KV-40
1 Stück / Profil "Mounting bridge"

Material Connector: ENAW 6063
DIBt^® - approval cross connector: Z-14.4-827
Material profile mounting bridge: ENAW 6063
Wx: 1,92 cm³ / lx:2,43 cm⁴
Wy: 2,11 cm³ / ly: 4,23 cm⁴

Technical Data

S-08 Hanger Bolt Metal UK: Recommended screw length: trapezoidal profile height / sandwich height + 20mm

Item No.: S-0880-KV / Hanger Bolt Metal UK / Clamping Range 15 - 60 mm
Item Nor.: S-08125-KV / Hanger Bolt Metal UK / Clamping Range 60 - 105 mm
Item No.: S-08160-KV / Hanger Bolt Metal UK / Clamping Range 95 - 140 mm
Item No.: S-08200-KV / Hanger Bolt Metal UK / Clamping Range 135 - 180 mm

Installation tool for S-08 metal hanger bolt
Drill / 10.00mm drill bit / 6.8 / 7.0 / 7.2 / 7.4mm metal drill bit / 5mm hexagon socket bit / 15mm wrench

Installation of S-08 metal hanger bolt

Determine the purlin alignment and mark it with a chalk line.
Pre-drill the roof cladding to a diameter of 10.00 mm.
Pre-drill the metal purlins depending on the material thickness.
Steel thickness 1.5-5.0 mm = pre-drill with a diameter of 6.8 mm.
Steel thickness 6.0 mm = pre-drill with a diameter of 7.0 mm.
Steel thickness 8.0 mm = pre-drill with a diameter of 7.2 mm.
Steel thickness > 10 mm = pre-drill with a diameter of 7.4 mm.
Screw the hanger bolt into the purlins until the seal rests on the profiled sheet.
For structural reasons, the clamp connector should point towards the ridge. (see graphic)

Accessories

Art.Nr.: P-40-6550-xxx / support profile 40x40mm
Art.Nr.: P-40-5500-xxx / support profile 40x40mm
Art.Nr.: P-80-6500-xxx / support profile 80x40mm
Art.Nr.: MMK-xxx-xxx / module middle clamp
Art.Nr.: MEK-xxx-xxx / module end clamp

P-40
P-80
MMK
MEK

Accessory Hanger bolt bridge

Art.Nr.: S-Brücke-333 / Hanger bolt bridge für Bead spacing 333 mm

Icluded in the set:

4 pieces / Washers M10 / DIN440 / 1.4301
1 Stück / cross connector KV-40
1 Stück / Profil "Mounting bridge"

Material Connector: ENAW 6063
DIBt^® - approval cross connector: Z-14.4-827
Material profile mounting bridge: ENAW 6063
Wx: 1,92 cm³ / lx:2,43 cm⁴
Wy: 2,11 cm³ / ly: 4,23 cm⁴